Refuse a truncated project, and drive the whole path from the probe

`upload_project_file` already existed - as a `GenericPrinter` trait method,
which is why a grep for `pub async fn` missed it and this commit nearly
reimplemented it. It logged `written` and `byte_count` next to each other and
never compared them, so a short write was something you could only notice by
reading the logs afterwards, and the next line printed the truncated file
anyway. A `.3mf` is a zip: cut the end off and the central directory goes with
it, so the printer gets an archive it cannot open. That is also the failure a
slow transfer invites, and this transfer is slow - 4.96 MB took 31.3s, so a
62 MB project is minutes of exposure.

`print-project <local> [name]` runs that method against a real printer, so
the harness tests the production entry point rather than the three pieces in
sequence. It deliberately takes no `--ams`: the whole point is that the
mapping comes out of the archive. Gated like `start`, on a terminal state and
`--yes-start-a-real-print`.

Confirmed end to end on the P1P (2026-10-15, with the owner's go-ahead), with
the same project the 2026-10-11 run used: the derivation read one PETG/GFG99/
`#2850E0` filament out of `Metadata/slice_info.config` and produced
`mapping=[3]`, padded to five trays; 297,227 bytes went up with an exact byte
count; `IDLE -> PREPARE -> RUNNING`. The AMS on that machine has slot 2 in
black and slot 3 in blue, same product and same `tray_info_idx`, so picking
slot 3 is the colour tie-break doing real work rather than a one-candidate
match.

examples/bambu_print_probe.rs

@@ -16,6 +16,14 @@
 //!   at all? A clean rejection naming the file means the
 //!   shape is right and only the target was wrong. A
 //!   parse error, or silence, means the shape is wrong.
+//! - `print-project <local> [name]`
+//!   **starts a real print.** The whole production path in
+//!   one call - derive the AMS mapping from the archive,
+//!   upload, start - via
+//!   `GenericPrinter::upload_project_file`. Gated on a
+//!   terminal state and `--yes-start-a-real-print`. Takes
+//!   no `--ams`: the point is that it reads the mapping
+//!   itself.
 //! - `upload <local> [name]`
 //!   **inert.** FTPS-transfers a local file onto the card
 //!   and stops - nothing prints until told to. Reports
@@ -294,6 +302,52 @@ async fn main() -> anyhow::Result<()> {
             }
         }
 
+        // `print-project <local> [name]` is the whole path in one call:
+        // derive the filament source from the archive, upload, start. Calls
+        // `GenericPrinter::upload_project_file`, so it tests the production
+        // entry point rather than the three pieces in sequence.
+        "print-project" => {
+            let Some(local) = args.get(3) else {
+                anyhow::bail!("`print-project` needs a local .3mf path");
+            };
+            const READY_TO_START: [&str; 3] = ["IDLE", "FINISH", "FAILED"];
+            if !READY_TO_START.contains(&state.as_str()) {
+                anyhow::bail!(
+                    "printer reports '{state}', which is not one of {READY_TO_START:?} - \
+                     refusing to start a print on a machine that may already be working"
+                );
+            }
+            if !confirmed {
+                anyhow::bail!(
+                    "refusing to start a real print without --yes-start-a-real-print.\n\
+                     This uploads a project and commits the machine to it. Be at the printer."
+                );
+            }
+            let data = std::fs::read(local)?;
+            let name = args
+                .get(4)
+                .filter(|a| !a.starts_with("--"))
+                .cloned()
+                .unwrap_or_else(|| format!("continuum-probe-{}", file_stem(local)));
+            println!("\n  upload_project_file({name}, {} bytes):", data.len());
+            println!("    no --ams flag: the mapping comes out of the archive, not this harness");
+            let started = std::time::Instant::now();
+            match bambu.upload_project_file(name.clone(), data).await {
+                Ok(()) => println!("    accepted after {:?} - watching", started.elapsed()),
+                Err(err) => {
+                    // The interesting failures are here: an unmappable
+                    // project should fail *before* the upload, leaving
+                    // nothing on the card.
+                    println!("    FAILED after {:?}: {err}", started.elapsed());
+                    println!("    if that was the mapping, the card should be untouched - check with `status`");
+                    return Ok(());
+                }
+            }
+            watch(bambu, state).await;
+            println!("\n  the file is still on the card as {name} - `delete` it when done");
+            return Ok(());
+        }
+
         // `upload <local> [name]` puts a file on the card and stops there.
         // Inert: a file on the SD card does nothing until something is told
         // to print it. The only proven transfer before this was 102 bytes,

src/printer/bambu.rs

@@ -1348,6 +1348,22 @@ impl GenericPrinter for BambuPrinter {
             "uploaded a project file to the SD card root"
         );
 
+        // These two were logged next to each other and never compared, which
+        // made a short write something you could only notice by reading the
+        // logs afterwards - and the next line would have printed the
+        // truncated file anyway. A `.3mf` is a zip: cut the end off and the
+        // central directory goes with it, so the printer gets an archive it
+        // cannot open rather than a partial model. It is also the failure a
+        // slow transfer invites, and this one is slow: 4.96 MB took 31.3s on
+        // a P1P (2026-10-15), so a 62 MB project is minutes of exposure.
+        if written != byte_count as u64 {
+            return Err(PrinterError(format!(
+                "{}: uploaded {written} bytes of {byte_count} - refusing to print a \
+                 truncated project",
+                self.base.name
+            )));
+        }
+
         self.start_uploaded_file(&file_name, &filament).await
     }